Vogtland Lowering Springs VW T6 Transporter/Multivan 35mm 956119

Vogtland Lowering Springs VW T6 Transporter/Multivan 35mm 956119. The description of this item has been automatically translated. Suitable for the following vehicles.

Vehicle: VW T6 Mulitivan, bus, van Type: 7HM, 7HC, 7HK, 7HKXO Construction year: from 2015 -> Lowering: VA: approx. Axle loads: front : 1575 kg, rear: 1630 kg Notes: 1, 21. Are you not sure whether the springs fit your vehicle?

Please inquire with us with the corresponding vehicle data. With VOGTLAND sport spring sets - - upgrade your vehicle: r. Asante optics with maximum driving pleasure. Whether in normal operation with pleasant driving comfort or in the limit with sporty progressive tuning. The special driving dynamics is achieved through the innovative spring design. The shortening of the spring travel requires a special suspension characteristic. Which is derived from racing. The VOGTLAND compound spring consists of two different spring rates. A start and an end rate. These are specially tailored to your vehicle type. Interacting characteristics stand for balanced driving comfort and for more driving dynamics even with a sporty driving style. The lowering ranges from 25 to 60 mm.

Increase agility and driving pleasure and experience your vehicle from scratch! Lower the front axle a little lower than the rear axle.

And you will be amazed how the particularly dynamic wedge shape transforms your vehicle into an optical power package. E with only two springs for the front axle. The amount of lowering is reduced by the amount of the factory lowering. The measure of the lowering will be reduced by the measure of the sport suspension.

Wedge shape: The lowering of the front axle depends on the equipment and engine variant. Wedge form: The lowering of the front axle depends from the equipment and weight of the engine.

For fine-tuning, please use Mercedes-Benz spring plate pads, which are available in different thicknesses (8 - 23 mm). For fine tuning, please refer to the Daimler Benz spring insolators available in different heights (8-23 mm). Reinforced version (heavy duty) for vehicles with full equipment and with more than 4 cylinders.

Heavy duty for models with full equipment and more than 4 cylinders. In vehicles with a load-dependent brake force distributor, a demonstration is required despite ABE. A presentation is necessary despite ABE for vehicles with a load depending brake power distributor. Not for vehicles with level control / air suspension. Without self-leveling / air suspension.

In vehicles with Tiptronic, Multitronic, increased lowering possible. Additional lowering may occur on vehicles equipped with automatic transmissions. Only for vehicles with full equipment. With XR3i no additional lowering, just tighter tuning.

XR3i does not lower, only the adjustment becomes more sportive. For vehicles with 6 cylinders, e. Golf III VR6, a conversion to sport dampers is recommended, included in the VOGTLAND complete chassis.

Vehicles with 6 cylinder engines require sport shocks. Not for: Break, Caravan, Tournament, T-Modell, Touring, Variant, Avant, Station Wagon, Traveler, (Kombi). As of ABE number 9138/2. Use up to 8.79 spring washers with the number: 171412341A. Up to 8.79 please use spring cap number 171412341A. Modified spring plates [and possibly other parts] must be used on the front axle. Either the spring plate with the VW part number 1H0412341 (large) or 357412341 A (small). Volkswagen springs caps [and probably further Parts] might be necessary: 1H0412341 (big) or 357412341 A (small). Shortened sports shock absorbers required. These are already included in the VOGTLAND complete chassis. Shorter sport shocks are required. The VOGTLAND suspension kits are covered with these shocks. Not for standard sports suspensions. Not suitable for serial or sport suspension. Only front axle springs, rear axle torsion bars (or spring element as standard). Only front springs, torsion bars (or standard spring) on the rear axle. Only rear axle springs, front axle torsion bars (or spring element as standard). Only rear springs, torsion bars (or standard spring) on the front axle.

All wheel / tire combinations that have been approved by the wheel inspection bodies can be used. The conditions in the wheel report or Wheels ABE are to be observed, with the exception of the requirement for series chassis. All wheel / tire combinations are allowed which are released by the wheel type testing institution. The conditions in the wheel approval have to be kept, except when suspension is required. With adjustable complete trolleys, the damping forces can only be adjusted on the front axle when installed.

At the VOGTLAND adjustable suspension kits are only the shock valvings in the front adjustable. Vehicle-specific tolerances may make it possible for the stabilizer and drive shaft to touch. 968550000, stabilizer kit, without xenon. For complete chassis: elongated serial coupling rods (VW / Audi). Due to vehicle-specific tolerances a contact between the drive shaft and the anti-roll bar might occur.

In such case it is required to install a modified anti-roll bar. For coilover sets use Order-No. 968 550 000 (Anti-roll bar conversion set without Xenon headlights). For suspension kits use a longer steering rod from your VW / Audi dealer. VA / HA coilover struts (height adjustable).

Height adjustable at the front and rear axle (threaded strut housings). VA / HA height adjustable (VA thread struts, HA springs with height adjustment plus Shock absorber). Height adjustable at the front and rear axle (front axle threaded housings, rear axle threaded spring perch and separate shocks). Only VA height adjustable, HA spring u. Only height adjustable at the front axle (threaded strut housings), springs and shocks at the rear axle. With standard tires Spacers required. May require the use of wheel spacers with equipment tires and wheels. The level control must be shut down.

Self-leveling must be shut down. VA height-adjustable coil spring strut, HA sport shock absorber (adjustment of the HA via torsion bar).

Height adjustable at the front (threaded strut housings), rear axle is adjustable with torsion spring adjustment. Installed shocks can be adjusted when installed. Damper can only be adjusted when removed. Installed shocks can not be adjusted when installed. The front direction indicators (§ 76/756 EG) must have a minimum height of 350 mm.

The front turn lights (§76 / 756 EG), must be the min. Production date 4/02 (piston rod thread visible), from 4/02 (piston rod thread covered). Fore vehicles manufactured before 04/02, the piston rod is fastened to the support bearing with an arched disk (piston rod threads visible). Models built after 04/02, piston rod threads not visible.

Use only for vehicles with rear shock mount M10 (1.0i, 1.2i, 1.7Di). Only for vehicles which have rear dampers mounted below with M10 (1.0i, 1.2i, 1.7Di). Use only for vehicles with rear shock mount M14.

(1.4i, 1.8i, 1.3CDTI, 1.7DTi, 1.7CDTi). Only for vehicles which have rear dampers mounted below with M14 (1.4i, 1.8i, 1.3CDTI, 1.7DTi, 1.7CDTi). VA shock absorber: complete shock absorber at item no. 960422, 960423, 966322, 966404, 966406, 966407, 969419, 969422, 969423, 960462. Front shock: complete suspension strut. Partner number: 966404, 966406, 966407, 966322, 960422, 969423, 960423, 960462. VA shock absorber: shock absorber cartridge.

Shocks are only suitable for European vehicles. Damper only siutable for European Cars.

With a drive shaft diameter of more than 42 mm, the max. If the driveshaft-diameter is greater than 42, mm the max. Aproved lowering is reduced 15 mm. The inner clearance dimension on the front shock absorber (between the fastening straps) must be 27 mm. The inside distance between the mounting bracket of the front damper must be 27 mm. From chassis number Y-on the 10th Job. From chassis number Y on the 10th position. For vehicles with 50 mm shock absorber. For cars with 50 mm suspension strut. For vehicles with 55 mm shock absorber.

For cars with 55 mm suspension strut. Upper vehicles BMW - No. 31331090467 must be used for vehicles from model year 10.91 to 5.92. For cars built from October 1991 up to May 1992 the upper attachment must be replaced by BMW partnumber 31.331.090.467.

Until 1998 (up to chassis number 8DX199999). Up to 1998 models (up to VIN: 8DX199999).

Coupling rods 968220, 968221 required for lowering over 40 mm. Steering rod 968220, 968221 for lowering above 40mm nessecary. After the chassis has been installed, there is freedom of movement check the tires for the VA strut min.

5 mm and if necessary by means of to restore tested spacers. After mounting the clearance between Wheel and Suspension Strut must be at least 5mm. If it is smaller you have to use wheel spacers.

Audi: year of construction up to 4.00, VW: year of construction up to 9.99. Audi: Modelyear up to 4.00, VW: Modelyear up to 9.99. Audi: year of construction from 5.00, VW: year of construction from 10.99.

Audi: Modelyear after 5.00, VW: Modelyear after 10.99. Without 16V, VA mounting hole spacing 52 mm. Without 16V, front bracket bolt distance 52 mm. Without 16V, VA mounting hole spacing 54 mm.

Without 16V, front bracket bolt distance 54 mm. Without rally, TD, Genty, CT, CTI, GTI. Without Rallye, TD, Genty, CT, CTI, GTI. Year of construction until 8.04, without 2.0T, 3.0V6 CDTi, without IDS. Modelyear up to 08.04, without 2.0T, 3.0V6 CDTI, without IDS. From year 8.04, without 2.0T, 3.0V6 CDTi, without IDS.

Modelyear after 08.04, without 2.0T, 3.0V6 CDTI, without IDS. For vehicles with eye attachment to the rear. For models with eye-mounting at the rear.

For vehicles with fork mounting on the rear. For models with fork-mounting at the rear. Not for vehicles from model year 2004. Not for models built after 2004.

Check the dimensions of the fastening straps on the VA strut: hole spacing 52 mm; Distance 23 mm. On front shock check measurements for the bracket: inside width 23 mm, mounting hole distance 52 mm. Only for vehicles with all-wheel drive (4WD). Only for cars with four wheel drive (4WD). Dome bearing 31331091709, disc 31331116983, sleeve 31331110196, rear axle BMW part no. Support bearing 33521091710, support pot 33521090282, disc 33521092986, protective tube 31331137 932, elastomer 33531091031. Additional OE equipment is needed on cars with EDC.

Engines BMW partner number: Bearing 31331091709, Washer 31331116983, Dust Cap 31331110196. Rear BMW partner number: Bearing 33521091710, 33521090282, Washer 33521092986, Dustseal 31331137 932, Bumpstop 33531091031. Sport damper (included) in conjunction with standard air spring on the rear. The OE-air suspension is not removed. A rear sport shock is provided and used with the air susupension.

Not for vehicles with electronic damper adjustment. Not for vehicles with electronic damping adjustment. In Allen vehicles before Bj. 6/92 fundamentally modified cathedral bearings must be used.

Dome bearing 31336764947, disc 31331116983, sleeve 31331110196. For all cars built before 6/92 the use of different Top-Bearing assembly in the front is required. BMW partner number: Bearing 31336764947, Washer 31331116983, Dustseal 31331110196. Damping force regulation, without IDS +. Damping force adjustment, without IDS +.

Shock absorber bearing 8E0512121E, spring support 8E0512149H, bumper 4B0512131Q. For cars with self-leveling additional OE-parts are required: Audi Partnumber: Bearing 8E0512121E, Springseat 8E0512149H, Bump stop 4B0512131Q. Model specific plug & play adapter included.

Hardness adjustment only on the VA. Model specific plug & play adapter available as option. For vehicles with air suspension only.

Only for Cars with Air Suspension. Only for vehicles with ABC chassis.

Only for Cars with ABC Suspension. From chassis number: Turbo: 4LA83740, S: 4LA48416, V6: 4LA01526, USA Turbo: 4LA93466, USA S: 4LA6 & 74337, USA V6: 4LA21527. From VIN: Turbo: 4LA83740, S: 4LA48416, V6: 4LA01526, USA Turbo: 4LA93466, USA S: 4LA6 & 74337, USA V6: 4LA21527. Only for multi-link rear axle. Only for Multilink rear suspension.

Only for torsion beam rear axle. Only for Twist-beam rear suspension. For vehicles with individual operating license (EBE), an acceptance according to §21 StvZo (individual acceptance) is required. Sets without deliverable as export items. For Cars with a single operating permit (EBE) an approval regarding §21 StvZo is required.

Sets without can be ordered for export market. Comments in brackets only apply to complete chassis.

Remarks in brackets only for kits. We reserve the right to make technical changes.

We accept no liability for printing errors. Subject to possible technical revisions. Reserves the right to change product specifications. We do not assume liability for misprint.

The item "Vogtland Lowering Springs VW T6 Transporter/Multivan 35mm 956119" is in sale since Thursday, January 17, 2019. This item is in the category "Vehicle Parts & Accessories\Car Tuning & Styling\Performance Suspension\Lowering Springs & Kits". The seller is "pbt-racing" and is located in Grafenwiesen. This item can be shipped to all countries in Europe.

Manufacturer: Vogtland
Manufacturer Part Number: 956119
Brand: Unbranded